Can I Install a Bath Tub Myself? Considerations And Actions
Can I Install a Bath Tub Myself? Considerations And Actions
Blog Article
Here below you will discover some brilliant content on the subject of Installing A Bathtub.
Setting up a bath tub isn't precisely brain surgery, but it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bathtub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily available, the task can move rapidly; if you need to open a wall surface to get rid of the old tub and also position the new bath tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub and also set in the new one. Make certain you have actually qualified yourself for the job as well as fit trying it. Rather than employing a specialist to take control of a halfway-completed project, it is much better to take into consideration employing one before you begin. Possibilities are you may need a specialist plumber to make tube links.
This post will certainly assist you mount a brand-new bath tub in your bathroom if you have already purchased a brand-new bathtub as well as do not require to alter the plan of your previous water system pipelines.
Your devices and also product list need to consist of the following:
Preparing for the Installment
To start with, the supporting frame supplied with the bathroom ought to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets device to prevent pressure on the tub.
Fit the adaptable faucet adapters to the bottom of both faucets using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you use all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom must now prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, then the first thing you need to do is disconnect the supply of water. After doing so, turn on the taps to drain any type of water remaining in the system. The process of eliminating the existing faucets can be fairly problematic due to the limited gain access to that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipelines have actually been eliminated, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Prior to moving on to fit the new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Bath tub
Utilizing both wooden boards under its feet, position the bathtub in the called for position. The wood boards are practical in evenly spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto four small factors.
The following goal is to make certain that the tub is leveled all round. This can be attained by inspecting the level as well as changing the feet on the bath tub till the level reviews level.
To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Switch on the supply of water and also examine all joints and new pipework for leaks as well as tighten them if required. Fill up the bath tub and additionally inspect the overflow electrical outlet as well as the regular electrical outlet for leakages.
Ultimately, fix the bath paneling as explained in the supplier's user's manual. Tiling as well as securing around the bathtub must wait till the bathtub has been utilized at the very least when as this will settle it into its last placement.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the maker given backnut. As soon as the faucet is firmly in place, the supply pipes can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular faucet adapters. The previous kind needs to be attached to the faucet finishes initially, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to fracture a stiff seal, triggering the water to pass through the wall surface between the bathroom as well as the tiling, resulting in issues with wetness as well as feasible leakages to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components and installations. They are sold in tubes as well as cartridges, and also are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealer can crack rather early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise easily available on the marketplace. It is recommended to fit the floor tiles making use of waterproof or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been made aware of that article on A Step-by-Step Guide to Installing a Bathtub through a good friend on another web page. Are you aware of anybody else who is in the market for the niche? Be sure share it. Thanks a lot for going through it.
Visit
Report this page